Van der Waals equation

In physics, chemistry, and chemical engineering, the van der Waals equation is an equation of state for a fluid composed of particles that have a non-zero size and a pairwise attractive interparticle force (such as the van der Waals force). It was derived by Johannes Diderik van der Waals in his doctoral thesis (Leiden 1873) by modification of the ideal gas law. The importance of this work is the recognition that the gas and liquid phase of a substance transform continuously into each other. Above the critical temperature, there is no difference between the gas and liquid phase, which is why it is proper to speak of the equation of a fluid, a generic term for liquid and gas.

Equation

Consider a vessel of volume V filled with n moles of particles (atoms or molecules) of a single compound. Let the pressure be p and the absolute temperature be T, then the van der Waals equation reads

$\left(p+{\frac {n^{2}a}{V^{2}}}\right)\left(V-nb\right)=nRT$,

where

a is a measure of the strength of attraction between the particles,

b is the volume excluded from V by one mole of particles,

R is the gas constant, R = N_A k, where k is the Boltzmann constant and N_A is Avogadro's constant.

The van der Waals parameter b is proportional to N_A times the volume of a single particle—the volume bounded by the atomic radius. In van der Waals' original derivation, given below, b/N_A is 4 times the volume of a single particle. Particles are seen as hard spheres. Observe that the pressure p goes to infinity when the container is completely filled, so that there is no void space left for the particles to move. This occurs when V = n b.

Although the parameters a and b are referred to as "the Van der Waals constants", they are not truly constants because they vary from one gas to another; they are, however, independent of P, V, and T. In other words, they are constant for the specific gas being considered.

Illustration

From the empirical critical temperature T_C and the empirical critical pressure p_C the constants a and b can be obtained by the equations

$a={\frac {27}{64}}{\frac {(RT_{C})^{2}}{p_{C}}}\quad {\hbox{and}}\quad b={\frac {RT_{C}}{8p_{C}}}$

The carbon dioxide molecule (CO₂) has p_C = 7.37 MPa and T_C = 304.1 K = 31 ˚C , which gives a = 0.366 m⁶ Pa and b = 42.9 10^-6 m³. For four different temperatures the van der Waals curves are given in the following figure. The critical pressure is at 73.7 bar = 7370 kPa (is close to 73.7 atm).

Different isotherms (curves of constant temperature) obeying the van der Waals equation of state. The dashed line from A to B is drawn in accordance with Maxwell's equal area rule.

For large volumes (on the right-hand side of the figure), the pressures are low and the fluid obeys approximately the ideal gas law pV = nRT for all temperatures shown. If we decrease the volume (go to the left in the figure along an isotherm), the pressure rises. Consider the (blue) isotherm of 10 ⁰C, which is below the critical temperature. Decrease the volume until we reach the point B, where condensation (formation of liquid CO₂) starts. At this point the van der Waals curve is no longer physical (excluding the possibility of the occurrence of an oversaturated, metastable gas), because in reality from B to the left (to smaller volume), the pressure stays constant—equal to the vapor pressure of the liquid. The real physical behavior is given by the dashed line of gas-liquid coexistence. The areas, bounded by the 10 °C isotherm, below and above the coexistence line are equal. This is the content of Maxwell's equal-area rule. Decreasing the volume further, we end at point A where all molecules are now in the liquid phase, no molecules are remaining in the gas phase. When the volume is diminished of a vessel that contains only liquid, the pressure rises steeply, because the compressibility of a liquid is considerable smaller than that of a gas.

If one follows the (green) 31 °C curve of critical temperature, one meets a horizontal point of inflection (first and second derivatives of p with respect to V are zero). Note that the figure exhibits two isotherms of temperature higher than the critical temperature; if they are followed, no liquid–gas phase transition will be seen; the higher pressure fluid will resemble a liquid, while at lower pressures the fluid will be more gaslike. At temperatures higher than the critical temperature, no gas–liquid interface occurs.

Although the maxima and minima in the van der Waals curves below the critical point are not physical, the equation for these curves, derived by van der Waals in 1873, was a great scientific achievement. Even today it is not possible to give a single equation that describes correctly the gas–liquid phase transition.

Validity

Above the critical temperature the van der Waals equation is an improvement of the ideal gas law, and for lower temperatures the equation is also qualitatively reasonable for the liquid state and the low-pressure gaseous state. However, the van der Waals model cannot be taken seriously in a quantitative sense; it is only useful for qualitative purposes.

In the first-order phase transition range of (p,V,T) (where the liquid phase and the gas phase are in equilibrium) it does not exhibit the empirical fact that p is constant (equal to the vapor pressure of the liquid) as a function of V for a given temperature.

Derivation

In the usual textbooks one finds two different derivations. One is the conventional derivation that goes back to van der Waals and the other is a statistical mechanics derivation. The latter has as its major advantage that it makes explicit the intermolecular potential, which is out of sight in the first derivation.

Conventional derivation

Consider first one mole of gas which is composed of non-interacting point particles that satisfy the ideal gas law

$p={\frac {RT}{V_{\mathrm {m} }}}.$

GNU Image
The cyan colored spheres are two fluid particles, of diameter d, in closest contact. The (black) enveloping sphere is excluded to other particles.

Next assume that all particles are hard spheres of the same finite radius r = d/2 (the van der Waals radius). The effect of the finite volume of the particles is to decrease the available void space in which the particles are free to move. We must replace V by V-b, where b is called the excluded volume. The corrected equation becomes

$p={\frac {RT}{V_{\mathrm {m} }-b}}.$

The excluded volume b is not just equal to N_A times the volume occupied by a single particle, but actually 4 N_A times that volume. To see this we must realize that two colliding particles are enveloped by a sphere of radius d that is forbidden for the centers of the other particles, see the figure. If the center of a third particle would come into the enveloping sphere, it would mean that the third particle penetrates any of the other two, which, by definition, hard spheres are unable to do. The excluded volume b/N_A per particle pair is 4π/3 × d³ = 32π/3 × r³, so that the excluded volume is not 8π/3 × r³ (the sum of volumes of the two particles), but four times as much.

It was a point of concern to van der Waals that the factor 4 yields actually an upper bound; empirical values for b are usually lower. Of course molecules are not infinitely hard, as van der Waals assumed, but are often fairly soft.

Next, we introduce a pairwise attractive force between the particles. Van der Waals assumed that, notwithstanding the existence of this force, the density of the fluid is homogeneous. Furthermore, he assumed that the range of the attractive force is so small that the great majority of the particles do not feel that the container is of finite size. That is, the bulk of the particles do not notice that they have more attracting particles to their right than to their left when they are relatively close to the left-hand wall of the container. The same statement holds with left and right interchanged. Given the homogeneity of the fluid, the bulk of the particles do not experience a net force pulling them to the right or to the left. This is different for the particles in surface layers directly adjacent to the walls. They feel a net force from the bulk particles pulling them into the container, because this force is not compensated by particles between them and the wall (another assumption here is that there is no interaction between walls and particles). This net force decreases the force exerted onto the wall by the particles in the surface layer. The net force on a surface particle, pulling it into the container, is proportional to the number density C ≡ N_A/V_m. The number of particles in the surface layers is, again by assuming homogeneity, also proportional to the density. In total, the force on the walls is decreased by a factor proportional to the square of the density and the pressure (force per unit surface) is decreased by

$a'C^{2}=a'\left({\frac {N_{\mathrm {A} }}{V_{\mathrm {m} }}}\right)^{2}={\frac {a}{V_{\mathrm {m} }^{2}}}\quad {\hbox{with}}\quad a\equiv a'N_{\mathrm {A} }^{2},$,

so that

$p={\frac {RT}{V_{\mathrm {m} }-b}}-{\frac {a}{V_{\mathrm {m} }^{2}}}\Longrightarrow (p+{\frac {a}{V_{\mathrm {m} }^{2}}})(V_{\mathrm {m} }-b)=RT.$

Upon writing n for the number of moles and nV_m = V, the equation obtains the form given above,

$(p+{\frac {n^{2}a}{V^{2}}})(V-nb)=nRT.$

It is of some historical interest to point out that van der Waals in his Nobel prize lecture gave credit to Laplace for the argument that pressure is reduced proportional to the square of the density.

Statistical thermodynamics derivation

The canonical partition function Q of an ideal gas consisting of N = nN_A identical particles, is

$Q={\frac {q^{N}}{N!}}\quad {\hbox{with}}\quad q={\frac {V}{\Lambda ^{3}}}$

where $\Lambda$ is the thermal de Broglie wavelength,

$\Lambda ={\sqrt {\frac {h^{2}}{2\pi mkT}}}$

with the usual definitions: h is Planck's constant, m the mass of a particle, k Boltzmann's constant and T the absolute temperature. In an ideal gas q is the partition function of a single particle in a vessel of volume V. In order to derive the van der Waals equation, we assume now that each particle moves independently in an average potential field offered by the other particles. The averaging over the particles is easy because we will assume that the particle density of the van der Waals fluid is homogeneous. The interaction between a pair of particles, which are hard spheres, is taken to be

$u(r)={\begin{cases}\infty &{\hbox{when}}\quad r<d,\\-\epsilon \left({\frac {d}{r}}\right)^{6}&{\hbox{when}}\quad r\geq d,\end{cases}}$

r is the distance between the centers of the spheres and d is the distance where the hard spheres touch each other (twice the van der Waals radius). The depth of the van der Waals well is $\epsilon$.

Because the particles are independent the total partition function still factorizes, $Q=q^{N}/N!$, but the intermolecular potential necessitates two modifications to q. First, because of the finite size of the particles, not all of V is available, but only $V-Nb'$, where ${\scriptstyle b'\,\equiv \,b/N_{\mathrm {A} }=2\pi d^{3}/3}$ (excluded volume per particle). Second, we insert a Boltzmann factor $\exp[-\phi /(2kT)]$ to take care of the average intermolecular potential. We divide here the potential by two because this interaction energy is shared between two particles. Thus

$q={\frac {(V-Nb')\,e^{-\phi /(2kT)}}{\Lambda ^{3}}}.$

The total attraction felt by a single particle is,

$\phi =\int _{d}^{\infty }u(r){\frac {N}{V}}4\pi r^{2}dr,$

where we assumed that in a shell of thickness dr there are N/V 4π r²dr particles. Performing the integral we get

$\phi =-2a'{\frac {N}{V}}\quad {\hbox{with}}\quad a'=\epsilon {\frac {2\pi d^{3}}{3}}=\epsilon b'.$

Hence, we obtain by the use of Stirling's approximation,

$\ln Q=N\ln {\frac {V-Nb'}{\Lambda ^{3}}}+{\frac {N^{2}a'}{VkT}}-N\ln N+N.$

It is convenient to take T out of Λ and to rewrite this expression as

$\ln Q=N\left(1+\ln {\Bigg [}{\frac {(V-Nb')\,T^{3/2}}{N\Phi }}{\Bigg ]}\right)+{\frac {N^{2}a'}{VkT}},$

where Φ is a constant. From statistical thermodynamics we know that

$p=kT{\frac {\partial \ln Q}{\partial V}}$,

so that, writing

$a\equiv N_{\mathrm {A} }^{2}a',$

we get,

$p={\frac {NkT}{V-Nb'}}-{\frac {N^{2}a'}{V^{2}}}\Longrightarrow (p+{\frac {N^{2}a'}{V^{2}}})(V-Nb')=NkT\Longrightarrow (p+{\frac {n^{2}a}{V^{2}}})(V-nb)=nRT.$

Other thermodynamic parameters

The extensive (i.e., linear in n) volume V  is related to the volume v per particle V= Nv, where N = nN_A  is the number of particles in the system. As before, the system consists of structureless particles with three translational degrees of freedom only.

We consider the statistical-thermodynamic equation for the Helmholtz free energy A,

$A=-kT\ln Q.\,$

From the equation derived above for lnQ, we find

$A(T,V,N)=-NkT\left(1+\ln \left({\frac {(V-nb)T^{3/2}}{N\Phi }}\right)\right)-{\frac {n^{2}a}{V}}$

This equation expresses A  in terms of its natural variables V  and T, and gives us all thermodynamic information about the system.

For instance, the mechanical equation of state (the van der Waals equation) was already derived above

$p=-\left({\frac {\partial A}{\partial V}}\right)_{T}={\frac {NkT}{V-nb}}-{\frac {n^{2}a}{V^{2}}}$

The entropy (S ) of a van der Waals fluid follows easily from A, it is:

$S=-\left({\frac {\partial A}{\partial T}}\right)_{V}=Nk\left[\ln \left({\frac {(V-nb)T^{3/2}}{N\Phi }}\right)+{\frac {5}{2}}\right]$

from which we can calculate the internal energy

$U\equiv A+TS={\frac {3}{2}}\,NkT-{\frac {n^{2}a}{V}}.$

Writing U in terms of its natural variables S and V requires elimination of T, that is, it needs an expression for T as a function of S and V. This can be obtained without great difficulty from the above expression for S.

Similar equations can be derived from A for other thermodynamic characteristic functions, but expressing, for instance, the enthalpy H ≡ A + TS + pV as function of its natural variables p and S, will require writing T and V as explicit functions of p and S, which yields a complicated expression for H. Also the Gibbs free energy G ≡ A+pV will be a complicated function of its natural variables T and p.

Reduced form

Although the material constants a and b in the van der Waals equation depend on the fluid considered, the equation can be recast into a single form applicable to all fluids.

The critical pressure and critical volume can be computed from the condition that the tangent in the critical point is horizontal and that it is a point of inflection:

$\left({\frac {\partial p}{\partial V}}\right)_{T}=0\quad {\hbox{and}}\quad \left({\frac {\partial ^{2}p}{\partial V^{2}}}\right)_{T}=0.$

This gives

$p_{C}={\frac {a}{27b^{2}}},\qquad \displaystyle {V_{C}=3b},\quad {\hbox{and}}\quad RT_{C}={\frac {8a}{27b}}.$

Defining the following reduced variables:

$p_{R}={\frac {p}{p_{C}}},\qquad V_{R}={\frac {V}{V_{C}}},\quad {\hbox{and}}\quad T_{R}={\frac {T}{T_{C}}}$,

the van der Waals equation of state given above (with n = 1) can be recast in the following reduced form:

$\left(p_{R}+{\frac {3}{V_{R}^{2}}}\right)(V_{R}-{\frac {1}{3}})={\frac {8}{3}}T_{R}$

This equation holds for all fluids. Thus, when measured in units of the critical values of various quantities, all fluids obey the same equation of state—the reduced van der Waals equation of state. Van der Waals termed this the principle of corresponding states.