Metal-oxide-semiconductor field-effect transistor

(PD) Image: John R. Brews
A modern MOSFET

(PD) Image: John R. Brews
A power MOSFET; source and body share a contact.

The Metal-oxide-semiconductor field-effect transistor (MOSFET) is a type of FET that consists of three layers: a metal top electrode (a conductor, called the gate), an oxide layer (working as an insulator separating the gate from the semiconductor layer), and a semiconductor layer (called the body). Its operation is based upon the modulation of the semiconductor conductivity by the electric field introduced in the body by the gate, the so-called field effect. This transistor was invented by Dawon Khang and Martin Atalla in 1960, at Bell Labs.

There are four contacts altogether: in addition to the gate and body contacts already described, there are two contacts atop the body at opposite sides of the gate called source and drain. Because the transistor is symmetrical, they can swap their functions. They do not permit current flow to the body in normal operation, as they form reverse biased diodes with the body. They do allow current between source and drain upon formation (by the gate) of a surface channel at the top surface of the body, next to the insulator. The channel conductivity depends upon the voltage difference between the gate and body (V_gb). The amount of current drawn in the channel depends upon the voltage drop across it, the drain to source voltage (V_ds). The channel strength also is affected by so-called "back gate bias", that is, by the body to source voltage (V_bs).

The modern MOSFET structure is shown in the figure (with a bow to artistic license). It is rather complex, as it is made to control a number of undesirable or parasitic effects that detract from its ideal behavior. Among these are unwanted capacitances between the gate and source and gate and drain, reduced by introduction of spacers at the sides of the gate. Another problem is high source-to-body and drain-to-body capacitance, which is reduced by raising the source and drain above the body, so the sidewall contact areas are reduced. These parasitic capacitances have to be charged and discharged between on and off conditions, and slow down device operation. Also undesired is penetration of the source and drain fields underneath the gate, which interferes with the channel formation. That effect is reduced by use of shallow junction extensions and screening halo implants, both designed to keep the source and drain fields close to their electrodes, and away from the gate.

For power applications a different geometry is used, notably asymmetric in drain and source geometry. Special attention is given to the drain, which is adapted to large drain voltages. The figure shows an example called the UMOSFET because of the U-shaped gate. This cross-section is is only one from a huge array of identical parallel fingers (the diagram is repeated to right and left with identical structures) all tied together in one device to handle large currents. As indicated by different colors in the figure, the source and drain are both n-type, and the body is p-type, or vice versa. The drain is specially doped to have a wide drift region, allowing reduction of the large drain voltage before it reaches the channel, and also allowing the current from the channel to spread out before reaching the drain contact, lowering the device resistance. The channel is present only when the gate voltage is large enough to turn the device "on", forming an inversion layer.

History

Modern electronic circuits use the MOSFET.

In 1930, Julius Edgar Lilienfeld (1881-1963), from the University of Leipzig applied for a patent in which he described an element bearing resemblance to the MOS transistor and which could have been the first transistor in history. We had to wait until the 1960s in order to see the arrival of such devices, whose development was made possible with the resolution of many technical issues outlined below. Today, the MOS transistor is the key element of digital integrated circuits on a large scale. Despite the origination at Bell Labs of many of the key patents for devices and processes underlying integrated circuits, including the MOSFET, the parent company AT&T never capitalized upon this research to become a big player in this industry, today perhaps the most complex and sophisticated manufacturing enterprise on the planet.

A major obstacle that had to be overcome in realizing this device was the quality of the semiconductor-insulator interface, which in many materials systems contains a large number of interface traps that interfere with the field effect. It was found that the interface between silicon and silicon dioxide was close to ideal in this respect if care was taken in its preparation (a technique called surface passivation). A stability issue required removal of mobile ion contaminants from the oxide, notably sodium, which required careful control of all fabrication steps, and today is accomplished in manufacturing by controlled atmosphere clean rooms that keep all contaminants to very low levels never envisioned prior to manufacture of this device. A major source of contaminants is the human body, so a modern "fab" requires operators to wear specially constructed bunny suits, with "booties", gowns, gloves, hair caps and masks. A modern fabrication center costs about one to ten billion US dollars, with a very hefty operational budget.

More recently, the challenges for MOSFET design are related to its miniaturization. Miniaturization of the transistor cannot be separated from the evolution of the entire circuit, as the layout of devices and circuits are combined in the same steps. A modern integrated circuit uses perhaps more than a billion of these devices with dimensions in the range of tens of nm. Miniaturization has required entirely new fabrication methods, such as ion implantation to control dopant locations very accurately, sophisticated self-aligned masking steps to construct tiny geometries, and development of chemical procedures and metallurgy with rigid thermal budgets. This package of processes is sometimes called silicon planar technology. The complexity of this processing and of circuits with millions of devices has led to development of computer-aided design involving sophisticated software that simulates everything from individual processes and devices to the layout of the entire circuit and the precise simulation of each step in its manufacture. Expense places a premium upon "right-the-first-time" manufacture: the concepts of electronic design automation and design for manufacture are applied with mind-boggling rigor.

Operation

(CC) Image: John R. Brews
A narrow, surface inversion layer of electrons forms at large enough positive gate voltages. The horizontal dashed line indicates the Fermi level that divides occupied energy levels from empty ones at zero temperature.

The control of the channel by the gate is similar to the formation of an inversion layer in the MOS capacitor, which is only a two-terminal device (gate and body contacts). The case of a p-type semiconductor body in which mobile holes are introduced in the valence band by introducing acceptor impurities is described below. The acceptors suck electrons out of the valence band, becoming fixed negative ions, and leaving electron vacancies in the valence band that behave as positively charge mobile holes.

The formation of this layer is understood by examining the behavior of the energy band edges under an applied field. The left-hand panels of the figure depict the lowest energy level of the conduction band of energies and the highest energy level of the valence band of energies (separated by the forbidden gap with no available energy levels) as a function of depth into the semiconductor body. In the figure's top panel, an applied voltage bends these band edges (left). This bending causes the valence band to become filled with electrons, so no holes are present. On the upper right, the figure shows the charge inducing this bending (Q) is balanced by a layer of negative acceptor-ion charge –Q_A in this depletion region where there are no holes. This depletion region of negative acceptor ions widens until neutrality is reached Q−Q_A = 0. In the bottom panel, a larger applied voltage further depletes holes from the surface but the conduction band becomes low enough in energy to populate with electrons near the surface, forming an inversion layer. The charge inducing the inversion layer is now balanced both by the inversion layer charge –Q_n and by the depletion layer charge –Q_A, so now Q–Q_n−Q_A = 0. Once the applied voltage is large enough to begin formation of the inversion layer, the charge balance is dominated by this layer, and the depletion region no longer expands significantly.

The electrons in the surface channel are mobile and form a conducting surface layer atop the insulating layer of fixed, immobile acceptor ions in the depletion region. The source and drain contacts on the body surface become connected by this conducting surface layer, so the formation of the inversion layer allows current to flow from the source to the drain. By contrast, when the conducting surface layer is not present, no conduction occurs, even when the surface layer is not depleted and holes are present. The contacts cannot conduct using holes because they are n-type semiconductor regions, and form pn-diode junctions with the body.

Thus, the source and drain are not electrically connected for voltages between zero and the threshold voltage for inversion layer formation. But once threshold voltage is exceeded, connection is established. The MOSFET constitutes an electrically controlled switch. The quantitative current-voltage behavior of the modern MOSFET is described by complex computer models.

Two device types: n- and p-channel

The device above uses a p-type body and an electron inversion layer, or n-channel. In CMOS circuits these n-channel MOSFETs are combined with p-channel MOSFETs that use an n-type body and a hole inversion layer. These CMOS circuits consume low power as only the active devices in a sub-circuit (either the n-channel or the p-channel devices) are operational at a given time, and the complementary devices are "off".

Frequency dependence

See also MOSFET hybrid pi model

(PD) Image: John R. Brews
Small-signal equivalent circuit for the four-terminal MOSFET in active mode.

An important device quality is its speed of response to transient signals. The MOSFET is a very non-linear device, so its transient response for large signals requires a numerical calculation. However, some idea is gained using a small-signal model and treating the device for small variations about a quiescent condition (its Q-point). Such a circuit is shown in the figure for a device biased in active mode. This circuit reduces the problem of frequency response to the RC time-constants related to charge and discharge of various capacitances through their associated resistors.

Four terminals are shown, the gate G, the source S, the drain D and the body B.

In many circuits the source terminal is short-circuited to the body terminal so voltage v_bs = 0 V. Then the circuit elements with b in the subscript can be ignored with the exception of C_bd, and the circuit becomes a version of the hybrid-pi model for the bipolar transistor with an infinite r_π resistance and an input capacitance C_gs similar to the C_π capacitance of the bipolar, but with no diffusion capacitance contribution. However, even with the body short-circuited to the drain, the capacitance C_bd is present as, in effect, a load capacitance upon the circuit. It should not be neglected, although many textbook discussions leave it out to keep things simpler.

A peculiarity of the MOSFET capacitances is the treatment of the channel. Commonly the capacitance C_gd includes coupling between the gate and the drain-end of the channel, while C_gs couples to the source-end of the channel. This matter can be decided with a full blown microscopic numerical analysis, but for circuit design faster modeling is needed. In these models, uncertainty over how this contribution is divided (that is, how much of the channel goes to the source-end capacitance and how much to the drain-end) leads to some slop in predicting the behavior of this device at frequencies above the corner frequency. If all the channel is attached to the source, the device is slower than when half goes to the source and half to the drain, for example. Arbitrarily, this ratio commonly is set at 60% source/40% drain.

Output resistance

(PD) Image: John R. Brews
Channel length modulation in 3/4μm technology. Notice the linear spacing of the curves with equal steps in V_GS.

In analog applications such as current mirrors or active loads, it is important for the transistor to have a large output resistance. Such circuits emulate a current source or current sink, and the Norton resistance of such a circuit should be large for ideal behavior.

The output resistance, usually denoted by r_O, is a measure of how much drain-to-source voltage change is necessary to cause a given change in transistor output current when the transistor is in active mode. The reason a change in drain bias changes the resistance is that the channel exists only when the oxide field is sufficient to form a channel. This field becomes lower as the drain is neared, and the channel weakens. Evidently, at the source itself this field is dependent upon the voltage drop V_GS, which in active mode is above the threshold voltage allowing formation of a channel. However, near the drain this oxide field depends upon V_GD, and for drain voltages large enough for active mode this drop is smaller than V_GS. The field in the oxide above the channel interpolates between these two values, and the channel basically disappears somewhere between the source and drain and dumps its carriers into the bulk semiconductor instead of remaining a channel. That position is called the pinch-off point and it moves toward the source as the drain voltage increases. The channel becoming shorter as drain bias increases, its resistance between source and pinch-off point drops, so the current increases, indicating a lowering output resistance with increase in drain bias. This phenomenon is called either channel-length modulation or the Early effect.

According to a simple empirical model patterned after the bipolar model for output resistance, the output resistance is given by:

$r_{O}=\left.{\frac {\partial V_{DS}}{\partial I_{DS}}}\right|_{V_{GS}={\text{constant}}}={\frac {1/\lambda +V_{DS}}{I_{DS}(V_{GS},\ V_{DS})}},$

where λ is called the channel-length modulation parameter with dimensions V⁻¹ and 1/λ plays the role of the Early voltage V_A found in the bipolar model. The current I_DS(V_GS, V_DS) is the drain current evaluated at the selected gate and drain voltages. It should be noted that this formula for output resistance is largely a fiction of hand analysis, and cannot be trusted. For example, the figure shows a tentative attempt to establish λ for a rather old 3/4μm technology. A single value for λ provides only a crude indicator of the slope of these curves in active mode, and the situation is much poorer for today's technology. The parameter λ is a function of channel length and bias voltages, and its value is at best an educated guess. In practice it is replaced by simulation using a numerical model of the transistor or, once example devices have been fabricated, by direct measurement.

Generally speaking, the output resistance of MOSFETs is low, and where high resistance is necessary, special circuit techniques are implemented to increase the active resistance.

Shichman-Hodges model

For hand analysis the DC current voltage behavior of the MOSFET in active mode is governed by the Shichman-Hodges model. The drain current is given by:

$i_{D}={\frac {1}{2}}k'_{n}{\frac {W}{L}}\left(v_{GS}-V_{T}\right)^{2}\left(1+\lambda V_{DS}\right)\ ,$

with W, L the width and "effective" length of the device, V_T the threshold voltage, and λ the channel-length modulation factor. The "technology parameter" k’_n is estimated from an empirical value for the carrier mobility in the channel and the oxide capacitance: k’_n = μ_effC_OX. Simply because some model is necessary for hand analysis to guide design prior to committing to numerical simulation, great effort has been wasted to invest this model with an accuracy that remains beyond its capabilities, no matter how convoluted the use of "effective" parameters. Aside from parameters with implicit bias and geometry dependence that is not spelled out, especially λ, the quadratic dependence upon gate-to-source voltage is not observed in modern MOSFETs. For example in the above figure, the IV-curves show a linear dependence upon gate voltage.