Simple machine

Template:TOC-right A simple machine is a mechanical device that changes the direction or magnitude of a force. In general, they can be defined as the simplest mechanisms that use mechanical advantage (also called leverage) to multiply force. A simple machine uses a single applied force to do work against a single load force. Ignoring friction losses, the work done on the load is equal to the work done by the applied force. They can be used to increase the amount of the output force, at the cost of a proportional decrease in the distance moved by the load. The ratio of the output to the input force is called the mechanical advantage.

Usually the term refers to the six classical simple machines which were defined by Renaissance scientists: These have modern applications to tools and complex machines.

Title if used DNS

Simple machine	Basic application	Animal power source	Complex application
Lever	Pry bar, Knife, Saw	Hand and arm linear force	Catapult
Wheel and axle	Drill (tool)	Hand and arm rotational force	Automobile
Pulley	Pile driver	Shoulder force (human) or harness	Elevator,Crane (engineering)
Wedge	Axe, Splitting wedge	Pressure	Metal shear
Screw	Screw (fastener)	Rotational movement	Propeller
Inclined plane	Ramp	Pushing or pulling	STOVL aircraft

They are the elementary "building blocks" of which all complicated machines are composed. For example, wheels, levers, and pulleys are all used in the mechanism of a bicycle.

Simple machines fall into two classes; those dependent on the vector resolution of forces (inclined plane, wedge, screw) and those in which there is an equilibrium of torques (lever, pulley, wheel).

History

The idea of a "simple machine" originated with the Greek philosopher Archimedes around the 3rd century BC, who studied the "Archimedean" simple machines: lever, pulley, and screw. He discovered the principle of mechanical advantage in the lever. His understanding was limited to the static balance of forces and did not include the trade-off between force and distance moved. Heron of Alexandria (ca. 10–75 AD) in his work Mechanics lists five mechanisms with which a load can be set in motion: The winch, lever, pulley, wedge, and screw. During the Renaissance the classic five simple machines (excluding the wedge) began to be studied as a group. The complete dynamic theory of simple machines was worked out by Italian scientist Galileo Galilei in 1600 in Le Meccaniche ("On Mechanics"). He was the first to understand that simple machines do not create energy, only transform it.

Alternate definitions

Any list of simple machines is somewhat arbitrary; the central idea is that every mechanism that manipulates force should be able to be understood as a combination of devices on the list. Some variations that have been proposed to the classical list of six simple machines:

• Some say there are only five simple machines, arguing that the wedge is a moving inclined plane.
• Others further simplify the list to four saying that the screw is a helical inclined plane. This position is less accepted because a screw simultaneously converts a rotational force (torque) to a linear force.
• Some go even further to insist that only two simple machines exist, as a pulley and wheel and axle can be viewed as unique forms of levers, leaving only the lever and the inclined plane.
• Hydraulic systems can also provide amplification of force, so some say they should be added to the list.

Frictionless analysis

Although each machine works differently, the way they function is similar mathematically. In each machine, a force $F_{in}\,$ is applied to the device at one point, and it does work moving a load, $F_{out}\,$ at another point. Although some machines only change the direction of the force, such as a stationary pulley, most machines multiply (or divide) the magnitude of the force by a factor, the mechanical advantage, that can be calculated from the machine's geometry. For example, the mechanical advantage of a lever is equal to the ratio of its lever arms.

Simple machines do not contain a source of energy, so they cannot do more work than they receive from the input force. When friction and elasticity are ignored, the work output (that is done on the load) is equal to the work input (from the applied force). The work is defined as the force multiplied by the distance it moves. So the applied force, times the distance the input point moves, $D_{in}\,$, must be equal to the load force, times the distance the load moves, $D_{out}\,$:

$F_{in}D_{in}=F_{out}D_{out}.\,$

So the ratio of output to input force, the mechanical advantage, is the inverse ratio of distances moved:

Mechanical Advantage $\equiv {\frac {F_{out}}{F_{in}}}={\frac {D_{in}}{D_{out}}}.\,$

In the screw, which uses rotational motion, the input force should be replaced by the torque, and the distance by the angle the shaft is turned.