Norton's theorem

In the theory of electrical circuits, Norton's theorem allows the replacement of a two-terminal portion of a linear circuit by a simplified circuit consisting of a current source, called the Norton current source, in parallel with an impedance, called the Norton impedance. Norton's theorem is the dual of Thévenin's theorem, which replaces a two-terminal portion of a linear circuit by a simplified circuit consisting of a voltage source in series with an impedance.

(PD) Image: John R. Brews
The result of applying Norton's theorem.

The upshot of using Norton's theorem is shown in the figure: the circuit behavior is boiled down to a simple current divider.

It will be noted that when the Norton impedance Z_N is much larger than the original parallel source resistance Z_S, the output current across the load Z_L benefits from a favorable current division when contrasted with direct attachment of the source to the load. In any event, the Norton circuit makes this current-division role of the more complex circuit clear. In general, this theorem is a tremendous aid to an intuitive understanding, essential for the creative design of circuits .

Finding the Norton components

To determine the Norton current, short circuit the two terminals and measure or calculate the short-circuit current between the terminals.

To determine the Norton impedance, set all independent sources between the two terminals to zero (leave the dependent sources active), and determine the impedance seen looking into the two terminals. For example, apply a known voltage across the port terminals and measure the current drawn, or apply a known current and determine the voltage developed. The Norton impedance is then the ratio of the voltage across the terminals to the current passing through the terminals.

In the case of a frequency dependent applied voltage or current, the impedance may be dependent upon frequency and exhibit a phase dependent upon frequency, as normally expressed using an impedance represented by a complex number.

Example

(PD) Image: John R. Brews
Bipolar current buffer.

(PD) Image: John R. Brews
Small-signal circuit to find output current.

The bipolar circuit in the figure at left represents a current buffer. The operation of this circuit is as follows. The DC current source I_E determines the current leaving the emitter in the quiescent state when no signal is applied. By appropriate selection of the DC current source it can be arranged that the transistor is configured to operate usefully, that is, it is in active mode.

A signal voltage i_S is applied to the emitter. The DC current source I_E does not permit any time varying current to pass through it, so at the signal frequency it behaves as an open circuit. No signal is lost through it. As a dual to this behavior, DC base voltage V_BB will not support a time-varying voltage across it, so it acts as an AC short circuit. The signal causes no change in base voltage. The time-varying current drawn through the base of the transistor is very small compared to that in the emitter (lower by a factor of the transistor β). As the signal alters the emitter current, the collector current follows suit, and the output current i_out in the load resistor R_L is a copy of the input signal i_in.

As this discussion indicates, the current gain of this circuit is very nearly unity, so amplification is not achieved. The purpose of this circuit is to isolate the signal source from the load R_L, with the object of preventing the load from affecting the performance of the source. In particular, if the source is forced to draw a large current, that may adversely impact its performance, and this circuit insures that only a small current is demanded of the source. Because the object of this circuit is not current amplification, but isolation of the driver, it is called a current buffer.

The transistor is a very nonlinear device, so the output signal current in the load resistor is not a faithful amplification of the input signal at the emitter unless the signal amplitude is small. For purposes of estimating the amplifier behavior, the assumption is made that the signal amplitudes are very small so the amplifier appears to behave as a linear circuit. Under these circumstances, the transistor can be approximated by a linear circuit composed of resistors called the hybrid pi model. The linear small-signal approximation to the circuit using the transistor hybrid pi model is shown in the figure with a few algebraic expressions derived by application of Kirchhoff's current law. This circuit is used to determine the Norton current (the short-circuit current) of the buffer.

The value of the Norton current is the output current through a short-circuit load, that is, with R_L = 0. From the small-signal circuit on the right, this current is i_O, which is found by equating the values of the emitter voltage found from the output and the input sides of the circuit:

$v_{E}=(i_{S}-i_{O})(r_{\pi }//R_{S})\ ,$

and:

$v_{E}=i_{O}R_{L}+(i_{O}-g_{m}v_{\pi })r_{O}\ .$

Equating these expressions, the Norton current is found as:

$i_{N}=i_{O}=i_{s}\left({\frac {r_{\pi }//R_{S}}{r_{\pi }//R_{S}+{\frac {r_{O}+R_{C}//R_{L}}{1+g_{m}r_{O}}}}}\right)\approx i_{s}\left({\frac {g_{m}(r_{\pi }//R_{S})}{1+g_{m}(r_{\pi }//R_{S})}}\right)\ ,$

where the approximation holds because R_L is taken as zero for a short-circuit output condition, and because g_mr_O >> 1. The input resistance R_S is likely to be quite large (if it were not the signal driver would be better represented as a Thévenin source with a small series R_S) so the parallel resistance R_S//r_π is approximately r_π, and the Norton current is approximately:

$i_{N}=i_{S}\ {\frac {\beta }{\beta +1}}\ ,$

where g_mr_π = ß. Inasmuch as ß is probably over 100, the Norton current is very nearly the same as the signal current (current gain is nearly unity).

(PD) Image: John R. Brews
Small-signal circuit with test current i_X to find Norton resistance.

To apply Norton's theorem, the resistance of the circuit looking back into the circuit from the output node is needed. That is accomplished using the second small-signal circuit. To determine the Norton impedance, the signal source is turned off (open-circuited), a test current i_x is applied to the output, and the resulting voltage at the output v_x is determined. Applying Ohm's law to obtain the voltage v_E at the emitter node, one finds:

$v_{E}=i_{O}(r_{\pi }//R_{S})\ ,$

and

$v_{E}=v_{X}-(i_{O}+g_{m}v_{E})r_{O}\ .$

Equating these two expressions the corresponding resistance is:

$Z_{O}={\frac {v_{X}}{i_{O}}}=(1+g_{m}r_{O})(r_{\pi }//R_{S})+r_{O}\ .$

The impedance Z_O is seen at the collector looking into the circuit at the point where current i_O is injected, after the parallel resistors (R_C//R_L).

The output resistance is found looking backward from the load, so R_L is removed from the circuit, leaving only R_C in parallel with Z_O. Therefore, the Norton impedance is:

$Z_{N}=Z_{O}//R_{C}\ .$

If this circuit is realized using a simple resistor R_C, the likelihood is that Z_O >> R_C, in which case the current division predicted by the Norton equivalent circuit places R_C in parallel with the load. The success of this circuit thus depends upon how large R_C is compared to the driver resistance R_S, and limitations imposed upon signal swings limit how large R_C can be. To avoid losing signal current to R_C and thus reducing signal current to the load, a large R_C is desirable. For this reason, this circuit is better implemented using a load circuit that involves more transistors, an active load. Such techniques can greatly increase the effective R_C; as the effective R_C increases, the upper limit upon the Norton resistance is Z_O, which is likely to be considerably larger than the driver impedance R_S because:

$(g_{m}r_{O})(r_{\pi }//R_{S})+r_{O}=r_{O}\left(1+g_{m}{\frac {r_{\pi }R_{S}}{r_{\pi }+R_{S}}}\right)=r_{O}\left(1+\beta {\frac {R_{S}}{r_{\pi }+R_{S}}}\right)\ ,$

which is considerably larger than r_O, itself a large resistance. Thus, favorable current division can be achieved with this buffer circuit modified to use an active load.