User:Milton Beychok/Sandbox

Pressure (symbol: 'p') is the force over an area applied to an object in a direction perpendicular to the surface. Gauge pressure is the pressure relative to the local atmospheric or ambient pressure.

Formula

Mathematically:

$p={\frac {F}{A}}$

where:

$p$ is the pressure,

$F$ is the normal force,

$A$ is the area.

Pressure is a scalar quantity, and has SI units of pascals; 1 Pa = 1 N/m², and has EES units of psi; 1 psi = 1 lb/in².

It is a fundamental parameter in thermodynamics and it is conjugate to volume.

Units

The SI unit for pressure is the pascal (Pa), equal to one newton per square metre (N·m^-2 or kg·m^-1·s^-2). This special name for the unit was added in 1971; before that, pressure in SI was expressed simply as N/m².

Examples

As an example of varying pressures, a finger can be pressed against a wall without making any lasting impression; however, the same finger pushing a thumbtack can easily damage the wall. Although the force applied to the surface is the same, the thumbtack applies more pressure because the point concentrates that force into a smaller area. Pressure is transmitted to solid boundaries or across arbitrary sections of fluid normal to these boundaries or sections at every point. Unlike stress, pressure is defined as a scalar quantity.

Another example is of a common knife. If we try and cut a fruit with the flat side it obviously won't cut. But if we take the thin side, it will cut smoothly. The reason is, the flat side has a greater surface area and so it does not cut the fruit. When we take the thin side, the surface area is reduced and so it cuts the fruit easily and quickly. This shows one of the good effects of Pressure.

The gradient of pressure is called the force density. For gases, pressure is sometimes measured not as an absolute pressure, but relative to atmospheric pressure; such measurements are called gauge pressure (also sometimes spelled gage pressure). An example of this is the air pressure in an automobile tire, which might be said to be "220 kPa", but is actually 220 kPa above atmospheric pressure. Since atmospheric pressure at sea level is about 100 kPa, the absolute pressure in the tire is therefore about 320 kPa. In technical work, this is written "a gauge pressure of 220 kPa". Where space is limited, such as on pressure gauges, name plates, graph labels, and table headings, the use of a modifier in parentheses, such as "kPa (gauge)" or "kPa (absolute)", is permitted. In non-SI technical work, a gauge pressure of 32 psi is sometimes written as "32 psig", though the other methods explained above that avoid attaching characters to the unit of pressure are preferred.

Gauge pressure is the relevant measure of pressure wherever one is interested in the stress on storage vessels and the plumbing components of fluidics systems. However, whenever equation-of-state properties, such as densities or changes in densities, must be calculated, pressures must be expressed in terms of their absolute values. For instance, if the atmospheric pressure is 100 kPa, a gas (such as helium) at 200 kPa (gauge) (300 kPa [absolute]) is 50 % more dense than the same gas at 100 kPa (gauge) (200 kPa [absolute]). Focusing on gauge values, one might erroneously conclude the first sample had twice the density of the second one.

Scalar nature

In a static gas, the gas as a whole does not appear to move. The individual molecules of the gas, however, are in constant random motion. Because we are dealing with an extremely large number of molecules and because the motion of the individual molecules is random in every direction, we do not detect any motion. If we enclose the gas within a container, we detect a pressure in the gas from the molecules colliding with the walls of our container. We can put the walls of our container anywhere inside the gas, and the force per unit area (the pressure) is the same. We can shrink the size of our "container" down to an infinitely small point, and the pressure has a single value at that point. Therefore, pressure is a scalar quantity, not a vector quantity. It has magnitude but no direction sense associated with it. Pressure acts in all directions at a point inside a gas. At the surface of a gas, the pressure force acts perpendicular (at right angle) to the surface.

A closely related quantity is the stress tensor σ, which relates the vector force F to the vector area A via

$\mathbf {F} =\mathbf {\sigma A} \,$

This tensor may be divided up into a scalar part (pressure) and a traceless tensor part shear. The shear tensor gives the force in directions parallel to the surface, usually due to viscous or frictional forces. The stress tensor is sometimes called the pressure tensor, but in the following, the term "pressure" will refer only to the scalar pressure.

Negative pressures

While pressures are generally positive, there are several situations in which negative pressures may be encountered:

• When dealing in relative (gauge) pressures. For instance, an absolute pressure of 80 kPa may be described as a gauge pressure of -21 kPa (i.e., 21 kPa below an atmospheric pressure of 101 kPa).

External links

• Pressure calculator
• A Java pressure simulation applet
• Thermodynamics - A chapter from an online textbook
• Introduction to Fluid Statics and Dynamics on Project PHYSNET
• An exercise in air pressure
• Pressure being a scalar quantity
• Online pressure converter for 52 different pressure units
• Pressure conversions - for both SI and non-SI units